YATUNINK Refill Ink Refill Kit 30ml Replacement for Canon PG-245XL PG-275XL Refill Ink Kit PG-243 PG-275 Refill Ink Work with Pixma TS3520 TS3522 TR4720 MG2522 MG2525 MX490 MX492 Printer(3x30ML BK)

YATUNINK Premium ink jet refill kit for Canon: I bought the kit with 3 black, plus a full set of 3 color, and 1 black.The included hand drill did not work, for me. I used a Milwaukee M12, and a drill bit, just larger than the needle on the ink bellows assembly. I have only used the black, so far, but it is very good quality, so far. Be sure to use nitrile gloves, and do the cartridge refill work in a place where ink spillage will not hurt anything, in case you spill some. It will not come off your hands, or skin, or anything else. I got some on my hands, and tried isaprophyl alcohol, paint thinner, laquer thinner, turpentine, nail polish remover, soap and water, and none of that worked. What did get it off my hands: 7% bleach (household), on a cotton ball - use at your own risk, and rinse it off quickly, then wash with soap and water, rinse well again, then use some good hand lotion. Just use the nitrile gloves to begin with, and keep it off your hands, clothes, or anything else. I set my cartridges in a disposable aluminum pie dish while working on them, to contain any drips, or spills.Any way: Canon cartridge has lots of recesses in the cartridge top. I picked one near the rear of the cartridge, and drilled it thru the plastic. Don't go too deep, as they say you could damage the screen in the bottom. I taped the top label down, dabbed the bottom nozzle area carefully with tissue paper, installed it, and it worked. I could not get the low ink lights to go out on the Canon TS3522; but from what I read from other users, you can work thru the low ink warnings, and keep printing. Time will tell. If you damage the nozzles, you will have to get a new cardridge.They say the cartridges can sometimes be un-cloggeg (if your nozzles are clogged), by placing the nozzle area in warm water for a few minutes, and carefully dab them dry with tissue. Don't immerse the cartridge too deep; only the bottom of the cartridge. Good luck, and happy money saving.A satisfied Customer.

Easy to grip and dispense the ink into my Cannon ink cartridges.

I did the drilling in the wrong spot but it still worked fine. prints look great so far. based off of how much ink they sent I can get 2 refills per small bottle on my ink cartridge so it should last me a good long while

The product concept is awesome, sadly my cartridges could not have hole drilled in it to refill. I have not been able to use product to know weather it is good or not. I will say the customer service was excellent. I told them I wanted a refund and I would return product, they gave me a refund and let me keep product too. The only thing I would suggest is offering empty cartridges that can be filled with the refill kit, that way the kit can be used easier and more often. I would buy this product over and over again if filling cartridges were easier. I will try to use again when my new ink cartridges run out.I wish I could of given more stars and I would have if I could of used product. Their customer service though is excellent. I hope this helps.

Did the trick, only have done black for now. I did not use the supplied drill bit thing as I thought it was too big. I got my smallest drill bit, removed the sticker that says canon 275, drilled a hole in one of the middle divots, filled cartridge slowly, about 1-2m, Ink overflowed so cleaned it up, I used Frog Tape to cover back up (does not come with new stickers ). Put in printer, pushed and held 5-10 seconds the triangle button to reset low ink. and is printing. Side note, when I took the cap off, ink did squirt out.My canon printer was the cheapest printer I could find so did not want to spend just as much on refill cartridges. I am not sure how the color refill will go as it is 3 colors in one cartridge.

This was the first time I ordered refill ink. So, I did not really know what to expect. The instructions were clear enough but the diagram did not match the original ink cartridges. I had to consult some one on where to drill the hole to fill the cartridge. It is also hard not to know how much ink to fill, since the cartridges were not of clear plastic and you could not see how much ink you are filling. Over all it’s a good value for the money versus buying cartridges. Beware, it may be a messy operation. Make sure you cover anything you don’t want to get the ink on.

Great product but instructions stink. I searched for a video on YouTube to help me. Turns out the top of the ink comes off and it is easier to fill that way. Don't try to drill a hole.

This product may be good, as other reviewers mentioned, but it didn't work for me. I found the instruction very inadequate and not well written;THE BLACK INK CARTRIDGE INSTRUCTIONS on the manual doesn't match my Canon printer. Besides, the drill. I used a fine bit on my drill and still, it could be a finer one; there is no way the "drilling tool" provided can work on a cartridge without making a Huge hole in it; gross. All in all, I don't know how deep the hole should be in the cartridge because the instructions didn't indicate, and finally it make a BIG mess all over the place, cartridge dripping, not showing in the supply levels, and now I am stuck with this and spending more money to buy real cartidgres.

Bien

bad very bad , I got wrong drill in the packge to drill the ink ,